Looking for Model 94/A crank case

The main Page for the Hodaka Club Discussion Group
Post Reply
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Looking for Model 94/A crank case

Post by Simonkav »

Hey everyone,
Catastrophic engine failure here - both case halves are toast. Metal sheared and jammed between the crank and the case, cracked the cases. Damage was done quick :(. On the hunt for cases to rebuild the motor with. I don't see them available on hodaka-parts. I have an email into Terry, will try calling next week. Message me if you have a lead on any!

1972 Model 94a Wombat 125

Cheers,
Simon
Roddy boy
Posts: 38
Joined: Sun May 22, 2016 6:49 am
Location: Calgary, Canada

Re: Looking for Model 94/A crank case

Post by Roddy boy »

If u are in Canada I have a complete bottom end for you. Ran it last year and all is good to go but seals are old
Calgary, Canada
thrownchain
Posts: 1920
Joined: Sun Jul 21, 2013 8:52 am

Re: Looking for Model 94/A crank case

Post by thrownchain »

Yep, where you is makes a difference.
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

Sorry, should have mentioned that. I’m in SF Bay Area, California.

Thanks,
Simon
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

I’ll also post photo of the cases. I’m assuming they cannot be repaired based on where the damage is. Welcome feedback....
thrownchain
Posts: 1920
Joined: Sun Jul 21, 2013 8:52 am

Re: Looking for Model 94/A crank case

Post by thrownchain »

Pic would be good. Almost everything can be repaired by competent people,
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

IMG-2494.jpg
IMG-2493.jpg
IMG-2492.jpg
IMG-2491.jpg
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

IMG-2495.jpg
IMG-2496.jpg
IMG-2497.jpg
IMG-2498.jpg
IMG-2499.jpg
thrownchain
Posts: 1920
Joined: Sun Jul 21, 2013 8:52 am

Re: Looking for Model 94/A crank case

Post by thrownchain »

Ouch, tis fixable with the right guy.
viclioce
Posts: 4845
Joined: Mon Apr 21, 2014 5:35 pm
Location: Santa Fe, NM
Contact:

Re: Looking for Model 94/A crank case

Post by viclioce »

Simon. Where do you live? Maybe someone close by can help you. :ugeek: Victor

1978 175SL
1976 03 Wombat
1975 99 Road Toad (2)
1973 96 Dirt Squirt (2)
1973 “Wombat Combat”
1973 Combat Wombat
1972 94 Wombat (2)
1972 Super Squirt
1971 92B+ Ace
1970 92B Ace 100B (2)
1968 92 Ace 100
1966 Ace 90
; D Victor
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

I’m in San Francisco.

Ouch is right :(

If anyone knows a great case repair guy, definitely not opposed to trying. I figured they were shot!

Thanks again everyone!

I did see a post from Rich (racerclam) about doing case work. Doesn’t appear to be active anymore?
viclioce
Posts: 4845
Joined: Mon Apr 21, 2014 5:35 pm
Location: Santa Fe, NM
Contact:

Re: Looking for Model 94/A crank case

Post by viclioce »

Here’s Rich’s website! You can contact him through there! :ugeek: Victor

https://richstayloredporting.com/index.html

1978 175SL
1976 03 Wombat
1975 99 Road Toad (2)
1973 96 Dirt Squirt (2)
1973 “Wombat Combat”
1973 Combat Wombat
1972 94 Wombat (2)
1972 Super Squirt
1971 92B+ Ace
1970 92B Ace 100B (2)
1968 92 Ace 100
1966 Ace 90
; D Victor
olddogs
Posts: 404
Joined: Mon May 05, 2014 8:30 am

Re: Looking for Model 94/A crank case

Post by olddogs »

You should be able to find a right side case half pretty cheap. The left side case is often chain damaged an will be more to replace as clean undamaged ones are getting rare.
thrownchain
Posts: 1920
Joined: Sun Jul 21, 2013 8:52 am

Re: Looking for Model 94/A crank case

Post by thrownchain »

I’ll have a set shortly, right side near new but non numbered, left side with previous damage already repaired.
Darrell
Posts: 315
Joined: Mon Jul 29, 2013 7:09 am
Location: Vancouver Island, BC

Re: Looking for Model 94/A crank case

Post by Darrell »

Hodaka-Parts has new 03 cases for sale.

Are they backwards compatible with 94 internals? I think there's a mod required (oil passage drilling) to run the 03 on premix however.
taber hodaka
Posts: 2240
Joined: Mon Jul 29, 2013 6:34 pm

Re: Looking for Model 94/A crank case

Post by taber hodaka »

I am sure I would have a set of cases, if nobody else does I would not rebuild your cases unless they were to a 1936 henweigh. ------- Clarence
User avatar
ossa95d
Posts: 385
Joined: Fri Jul 19, 2013 3:06 pm
Location: Manchester Vermont

Re: Looking for Model 94/A crank case

Post by ossa95d »

Hahaha good stuff Clarence... I'm not falling for it. :lol:
Ivan AKA "Pop"
captonzap
Posts: 24
Joined: Mon Apr 05, 2021 4:50 am

Re: Looking for Model 94/A crank case

Post by captonzap »

Oh, come on, what's a henweigh? :lol:
taber hodaka
Posts: 2240
Joined: Mon Jul 29, 2013 6:34 pm

Re: Looking for Model 94/A crank case

Post by taber hodaka »

Just about 7&1/2 pounds before she lays the egg. ---------------- old joke Clarence
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

taber hodaka wrote: Mon May 03, 2021 6:03 pm I am sure I would have a set of cases, if nobody else does I would not rebuild your cases unless they were to a 1936 henweigh. ------- Clarence
Appreciate the input. How might I connect with you regarding said cases? Feel free to PM or email me through the board.

Cheers,
Simon
Simonkav
Posts: 40
Joined: Sat Nov 18, 2017 3:51 pm

Re: Looking for Model 94/A crank case

Post by Simonkav »

Roddy boy wrote: Fri Apr 30, 2021 5:20 am If u are in Canada I have a complete bottom end for you. Ran it last year and all is good to go but seals are old
Just for my learning - why the Canada limitation? I’m not hip to the challenges - shipping to US outrageous or customs not cool with it or just a PITA you’d rather not deal with?
matt glascock
Posts: 2520
Joined: Thu Oct 24, 2013 5:20 pm

Re: Looking for Model 94/A crank case

Post by matt glascock »

I wouldn't toss the roached cases. Some a$$-kicking aluminum fabber with a serious sand-casting jones might like to put them back into circulation. They ain't makin' any more.
Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests