kick crank

The main Page for the Hodaka Club Discussion Group
Post Reply
givergas
Posts: 790
Joined: Sat Sep 16, 2017 11:41 am
Location: minnesota

kick crank

Post by givergas »

is there a way or a trick to take the kick starter off with out unwinding the spring or taking off the side case? its wore out and and points towards the back end not 90 degrees to the bike so your foot has a tendency to slip off when wet or muddy. thanks ...albert
thrownchain
Posts: 1920
Joined: Sun Jul 21, 2013 8:52 am

Re: kick crank

Post by thrownchain »

So are you replacing the lever or spring? The best is to take the cover off while the bike is flat on it's left side. That way the oil stays in the motor. You have to index the lever on the spring and it's not easy without removing the cover.
User avatar
Bullfrog
Posts: 2784
Joined: Mon Jul 22, 2013 4:05 pm
Location: Oregon, 12 miles from the center of the Hodaka Universe(Athena)

Re: kick crank

Post by Bullfrog »

I once attempted to remove/replace the kick start lever with the engine in the frame, and with the clutch cover in place. Spent a couple of hours fiddling at it as I remember. Then laid the bike on its left side, removed the clutch cover and had it done in 10 minutes or so. A great example of a "bad experience" being a good experience.
Ed
Keep the rubber side down!
givergas
Posts: 790
Joined: Sat Sep 16, 2017 11:41 am
Location: minnesota

Re: kick crank

Post by givergas »

what im trying to do is weld this up to grind it flat so its not angled back so off with the case. thanks for saving me some frustration .... albert
Attachments
Inkedkick starter_LI.jpg
viclioce
Posts: 4848
Joined: Mon Apr 21, 2014 5:35 pm
Location: Santa Fe, NM
Contact:

Re: kick crank

Post by viclioce »

Seems like it would just be simpler to get another kick start lever.... :ugeek: Victor

1978 175SL
1976 03 Wombat
1975 99 Road Toad (2)
1973 96 Dirt Squirt (2)
1973 “Wombat Combat”
1973 Combat Wombat
1972 94 Wombat (2)
1972 Super Squirt
1971 92B+ Ace
1970 92B Ace 100B (2)
1968 92 Ace 100
1966 Ace 90
; D Victor
matt glascock
Posts: 2520
Joined: Thu Oct 24, 2013 5:20 pm

Re: kick crank

Post by matt glascock »

Albert, what is the condition of the stop tab on the swing-out foot piece? Would that be a bit easier to build up with a bit of weld?
givergas
Posts: 790
Joined: Sat Sep 16, 2017 11:41 am
Location: minnesota

Re: kick crank

Post by givergas »

matt that is a good idea i will start there and see how that works out. i should be able to accomplish what im after ...thanks...and victor this is the other one ....albert
matt glascock
Posts: 2520
Joined: Thu Oct 24, 2013 5:20 pm

Re: kick crank

Post by matt glascock »

Albert, it probably wouldn't take a very large bead to bring the foot pedal back to 90 degrees. Let me know how it works out. I might have a foot pedal in my stash that is collecting dust.
givergas
Posts: 790
Joined: Sat Sep 16, 2017 11:41 am
Location: minnesota

Re: kick crank

Post by givergas »

took the swing-out foot piece off and put a bit of weld on it then figured wile it was off i might as well put some weld on the kick lever its self just a dab and 4 inch grinder, got a good shoulder on them both and now it is a nice sturdy 90 degrees thanks for the brain storming.....albert
Attachments
thumbnail (11).jpg
matt glascock
Posts: 2520
Joined: Thu Oct 24, 2013 5:20 pm

Re: kick crank

Post by matt glascock »

Well played, Albert. In the immortal words of John "Hannibal" Smith, "I love it when a plan comes together".
Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests