This Winter I'm splitting the case and redoing my Wombat94 engine. The report from the PO about it being a fresh rebuild was a tad optimistic. I like to start gathering major parts in advance.
I know I will need a gasket, seal and bearing kit. We're going to pop the crank and redo it, so I'll get a crank kit. And shifter springs and parts, and kickstart springs and parts. Clutch I don't know about, though I plan to blueprint it, so I might get the plates/springs now and the bushings/shims/release parts while waiting for the shop work. Top end is new-- piston, rings and fresh hone-- so that will be reused.
This should cover the major, big ticket parts. Have I missed anything?
Rebuild parts list
Rebuild parts list
Keepin' the Shiny Side up
on a '72 Wombat 94
--Bill
on a '72 Wombat 94
--Bill
Re: Rebuild parts list
Forgot to mention-- I plan to use the available Hodaka crank kit, unless an aftermarket brand is better. Highest use will be a TAT trans-continental run, no 14000 rpm extended runs.
Keepin' the Shiny Side up
on a '72 Wombat 94
--Bill
on a '72 Wombat 94
--Bill
Re: Rebuild parts list
What part of the TAT are you planning to ride? I know a few people that have ridden it and they all suggest at least a semi-modern 400cc bike as the smallest bike to try it on. But, then again, they rode the whole thing, from Tennessee to Oregon.
-
socalhodaka
- Posts: 927
- Joined: Fri Jul 19, 2013 10:31 am
Re: Rebuild parts list
Andy Blackburn rode his Road Toad on the TAT from Tennessee to Hodaka Days http://advrider.com/index.php?threads/1 ... at.893598/
Re: Rebuild parts list
Yes! I've been reading that Ride Report on ADVRider.
Initial plan is to ride Alabama--> Oregon. Msybe solo, maybe no support vehicle. Crazy, maybe foolish. I had been plotting and planning a Transcon ride to the PNW on my Beemer.
Not being insane, I'll start with "local" 200-300-500 mile trips to test the concept. It's out there, waiting to be done.
Initial plan is to ride Alabama--> Oregon. Msybe solo, maybe no support vehicle. Crazy, maybe foolish. I had been plotting and planning a Transcon ride to the PNW on my Beemer.
Not being insane, I'll start with "local" 200-300-500 mile trips to test the concept. It's out there, waiting to be done.
Keepin' the Shiny Side up
on a '72 Wombat 94
--Bill
on a '72 Wombat 94
--Bill
Re: Rebuild parts list
Don't forget some Yamabond or similar for case sealant. Good luck with your rebuild, Bill! I hope it all goes smoothly for you! And don't forget the bottom end bushings replacements too! ; D Victor
1978 175SL
1976 03 Wombat
1975 99 Road Toad (2)
1973 96 Dirt Squirt (2)
1973 “Wombat Combat”
1973 Combat Wombat
1972 94 Wombat (2)
1972 Super Squirt
1971 92B+ Ace
1970 92B Ace 100B (2)
1968 92 Ace 100
1966 Ace 90
; D Victor
Re: Rebuild parts list
That list is just the big-ticket, high-dollar items. I'm sure I'll need a lot of many small nickle-and-dime parts as l get into thenrnginr. Hopefully I won't have surprises like gears and countershafts.
Keepin' the Shiny Side up
on a '72 Wombat 94
--Bill
on a '72 Wombat 94
--Bill
Who is online
Users browsing this forum: No registered users and 5 guests