How to pull apart Super Rat rear suspension

The main Page for the Hodaka Club Discussion Group
Post Reply
Johnno84
Posts: 2
Joined: Fri Aug 05, 2016 7:37 pm

How to pull apart Super Rat rear suspension

Post by Johnno84 »

Can any one tell me how the rear shocks are pulled apart ?
Attachments
image.jpeg
Jack Elliott
Posts: 73
Joined: Tue Dec 29, 2015 11:42 pm
Location: Sydney Australia

Re: How to pull apart Super Rat rear suspension

Post by Jack Elliott »

Hi johnno
My understanding is they are non servicable.
Its possible to pull them apart to a degree but if they are worn out you get new ones,
There are good shocks available from SH and other suppliers that look original and function well .
there are also Progresive brand shocks that dont look completely original but offer better performance for vintage MX etc.
Jack
User avatar
Bullfrog
Posts: 2784
Joined: Mon Jul 22, 2013 4:05 pm
Location: Oregon, 12 miles from the center of the Hodaka Universe(Athena)

Re: How to pull apart Super Rat rear suspension

Post by Bullfrog »

There is a small drive pin which prevents the upper mount from being un-screwed from the shock shaft. The drive pin can be driven out to allow removal of the upper mount. You MUST devise some means of holding the spring compressed (for safety) as the upper mount is removed.
Ed
Keep the rubber side down!
User avatar
Bullfrog
Posts: 2784
Joined: Mon Jul 22, 2013 4:05 pm
Location: Oregon, 12 miles from the center of the Hodaka Universe(Athena)

Re: How to pull apart Super Rat rear suspension

Post by Bullfrog »

PS: As already mentioned, you won't be able to re-build the shocks. Removing the upper mount and spring only provides a means to clean up things a little better cosmetically.
Keep the rubber side down!
robert campbell
Posts: 42
Joined: Wed Jul 27, 2016 9:53 am

Re: How to pull apart Super Rat rear suspension

Post by robert campbell »

The shocks on my B+ looked about the same. I was amazed at how well a 2 foot long and 2 inch wide rag with a lot of Semi-Chrome paste made them look. Not museum quality, but pretty darn nice!

Rob
Johnno84
Posts: 2
Joined: Fri Aug 05, 2016 7:37 pm

Re: How to pull apart Super Rat rear suspension

Post by Johnno84 »

Thanks for that all I want to do is clean them up trying to keep it all original
User avatar
hodakamax
Posts: 2211
Joined: Thu Aug 28, 2014 9:56 am
Location: Parsons Kansas

Re: How to pull apart Super Rat rear suspension

Post by hodakamax »

Hard to believe but a few minutes on a bench grinder with wire brush and these cleaned up nicely (not perfect but quite the transition). I didn't even pull them apart. They were badly pitted but they still don't look bad. Somewhat amazing. Check it out!

Max
Attachments
Before
Before
After
After
viclioce
Posts: 4848
Joined: Mon Apr 21, 2014 5:35 pm
Location: Santa Fe, NM
Contact:

Re: How to pull apart Super Rat rear suspension

Post by viclioce »

Another option us aluminum foil & water! The aluminum will remove the rust without scratching the chrome. The water just helps move things along. ;D Victor
Attachments
Before
Before
After
After

1978 175SL
1976 03 Wombat
1975 99 Road Toad (2)
1973 96 Dirt Squirt (2)
1973 “Wombat Combat”
1973 Combat Wombat
1972 94 Wombat (2)
1972 Super Squirt
1971 92B+ Ace
1970 92B Ace 100B (2)
1968 92 Ace 100
1966 Ace 90
; D Victor
matt glascock
Posts: 2520
Joined: Thu Oct 24, 2013 5:20 pm

Re: How to pull apart Super Rat rear suspension

Post by matt glascock »

Hey Maxie, I have a pair of shocks for a rider resto that look a lot like yours in the "before" picture. What type of wire wheel did you use on your bench grinder. I would think brass. Also, did you use any polishing compound and were the shocks dismantled prior to the wheeling and dealing? Thanks!

Best,

Matt
Post Reply

Who is online

Users browsing this forum: No registered users and 8 guests