I was looking for one to restore, I am in Texas.

Any 68 or 69 ace 100 projects out there?

Nice Sherpa S efkruger. Is that a model 63? I have a m63 with a m44 top end. Just put the original Amal back on and original air cleaner but no pictures yet. That tank is bubbling the paint but I have another that will never see gas. That bubbling paint was with vp race gas so must have had some bad...

Looking for a set of forks.
Terry

Any of the Hodaka specialist that do restorations and motor work able do fork straightening? I guess a local motorcycle shop could maybe do it also.
Terry

Anyone have experience straightening slightly bent 30mm Ceriani fork tubes. Hate to trash them and can't seem to find new or used straight tubes.
Terry

You have already proved the piston and rings will go in the jug so try again. Mark the locating pins with a sharpie to help keep every thing lined up and it should be fine.
Terry

Use graphics that have the little holes in them, can't recall what they call them but they use them on Yamaha plastic gas tanks and Can Ams.
Terry

I have some Bultaco's and you must heat the piston to get the pin in so a tight pin should not be a problem but most Jap bikes are the thumb push style. Most likely the clips did not seat properly because wrong clips or? I have never had a clip come out with over 50 years of riding, racing.
Terry

Paul you have been nothing but good to me and I for one hope you keep selling all those parts you had reproduced or sourced we need. You can not please all the people all the time and it is a shame that you have to experience those types.
Terry

Heat the cases and throw the bearings in the freezer over night and they usually just drop right in. I use my gas grill to heat the cases or you can use a torch.
Terry

Can you press the bearing out with the crank still in the bearing then use a bearing puller to remove the bearing?
Terry

I would steer clear of castor oils unless you like carbon build up. 32 to 1 with Yamalube R or Golden Spectro a better choice IMO. Those old mixing recommendations are from way back when oil was not as good as today's lubricants.
Terry

Looks really good except for the front fender. Looks wrong on the bike but just my opinion.
Terry

No still no word. I have moved on and not interested at this point. Would be a good deal for someone.
Terry

Probably not getting close to Texas are you?
Terry

Well that explains things it was the Rickman. I hope he is OK I hate to hear about anyone getting hurt. I apologize for questioning his actions and sorry I said anything.
Terry

Why would someone post and add on Paul's market place and then never respond to questions? Must not want to sell or maybe they have already sold the bike. I just thought it strange behavior.
Terry

Did you pressure check the engine? I would pressure test and go from there. Oil brand is a hot topic but I have never seized a motor with race fuel and Yamalube R at 32 to 1. Surely you are running ethanol free fuel and a good quality oil but I would think about a oil change if jetting seems OK. I a...

Very nice Rich, that would be in my living room. I know that nickel plating is expensive and hard to find anyone that even still does it. I have a Trackmaster frame I wanted re-nickeled before I found out the cost and no one wanted to fool with it.
Terry

Nice, Racerclam did you nickel plate that frame or is that powder coating?
Terry

Max I too was at the Houston short track. Barry had engine trouble or I think he would have been a threat. He also rode at the Daytona short track and I was at that race too. He again had bike trouble but he was fast. It grooved up but Barry could ride up high and never shut off and was a threat. Th...

Hey Max what kind of seat is that on your bike? I like the look of it.
Terry

Hey Terry that would be so cool to have, I appreciate you doing that for me.
Terry Smith
137 Leda DR
Dallas TX 75218

That is exactly what I did Max. It worked out really well and I had enough left over to make another for a set of forks I am going to use on another brand that I am fitting a set of Cerianis forks to. I was afraid it would not clamp down on the axle good enough with the slot cut in it but it worked ...