Just reset the points with the new condenser and points, kicked it oeer and have great spark. Looks good so far. Put it back together and see what happens. Will let you know . Thanks alot for all your help, helped alot.
MTRob

The needle does not come close to the main jet. I went to put the smaller jet in and noticed that it only goes in so far. The distance it sticks out of the holder is exactly the same as the long 140 jet. Guys will see what happens. Just reset the points with the new condenser and points, kicked it o...

Thanks Guys. I'am going to try the short jet #135 and see how it runs and let you know. Like you said the jet is not that smaller than the long jet. I think they used them for room reasons on some carbs.
MTRob

The jets are Mikuni its that the head is shorter. Both say 135, Is it because they made them shorter for room reasons?
Would like to know the difference. any body have the answer?
MTROB

What I did was take 2 very small screwdrivers and ground them down to a very fine point and slowly worked it out one side at a time. I also disconnected
the switch and sprayed it with WD40 and slowly hit the top till it moved out and then grabbed it
MTRob

There is a key listed on Ebay #929437 for you switch. Under Hodaka Key
MTRob

A friend gave a box of jets for Mikuni Carbs. Main jets from 130 to 180. Some are short head jets and some are long head jets. What is the difference in the jets? Will they work the same?
Thanks
MTRob

ED One more question for you. I have another 125 94A engine I need to send to get it overhauled. I already redid the cylinder 30 over new piston, rings and redid the clutch and stator. So I only need to send in the main body without the cylinder and clutch and stator. Who would you recommend that co...

ED Thats what it looks like, like grade school wood burner. Won't use that. I have an old Weller iron that puts out 100/140 watts. This one should work well. It was my fathers, he used it when he built model airplanes back in the day. Olde but golde. I will test it using your advice. Got my condense...

Bullfrog your right. I have one of the older looking soldering gun that looks like a screw dryier. I'll use that. Should have my new condenser tomorrow.
Let you know how things go. Thanks everyone for your advice. Just keep on learning.
Mt rob

Hello Powder Coaters, I would be interested in what brand of powder coating, your powder coater uses that seems to work the best on our machines products. I am interested in the most poplar brand used and what other colors are available. Thank you, Bruce Young Hodakaparts.com IDAHO byret208@hotmail...

Thanks again guys. I pulled it all apart and put in new points and went to put in the new condenser and noticed on the top where you solder the top of the condenser it moved back and forth inside the casing. This must be a bad condenser Right? I just got the condenser now wait week for new one. Put ...

Thanks, At first since it was a new honed 40 with new pistons and rings, I made the gas fuel mixture at about 30 to one. And the plugs looked oiled fouled, then I drained the tank and put in 20 to one. Now they look fuel fouled. I will try other things Condenser, points, float, jetting. I would pull...

Roger thats what my 94A Wombat is doing but I already cleaned the pipe had it powder coated and the inside pipe cleaned. Still working out my problem.
Thanks
MTRob

Thanks Guys, Taber tried 180 did not work at all, went back to 140. I am going to put in new condenser and jet it at 135, since I have it apart I'll change the points to. Plus check float setting. Will let you know We are at 4000 ft. Hope this works 2 years in rebuild.
Thanks
MTRob

I have a 125 Wombat 94A and can't get it to quit fouling plugs. The motor has been bored oer 40, Points and condenser new, set at 13 gap. Why am I fouling plugs and it runs for a while then starts bogging down and backfires then stops. I change the plug do a little adjusting to the carb but still do...

Sounds great hae a great time. Just one question what about turn signals don't you need them?
MTRob

I read the Teach tips on Clutch blue printing, What does that do to help the clutch? Just wondering how much it helps and way?
MTRob

I have a 125 Wombat 94A and in the exhaust pipe end is the spark arrestor with a diffuser in the arrestor that is adjustable. You can screw it in and out
what is it for and what adjustment should it be
MTRob