You are correct, screws and wire. My retired brain and fingers made me do it. But please if you do rewire it, use the special tie wire that you can get at any Home Depot or Lowes, or good hardware or auto supply. All is good and I stand corrected. Good Luck with project. Happy Hodaken.

Hello again, its not that the nylon nuts will cause more damage, its the question one must ask is it worth more than to use proper special stainless tie wire to make sure that issues probably will not happen, or take the chance if something fails and its all a costly repair to be done. Proper tie wi...

Optional ways of locking things down on the clutch using nylon nuts, spec lock nuts, bailing wire and etc, ask yourself latter, how much did I save when all comes loose and tears things up or leaves you in the woods with a long walk home. Do as Ed suggest,s and do it the right way, it will save you ...

Video was perfect Kelley, no need to apologize, it was very understandable. Really shows importance of proper tools. Good Job Bruce

Good info Kelly, keep them coming. One question, was that Greg Singing at the first of the video in the background, If so he should go on the Radio. OK. thanks Bruce Young

We need pictures and a better idea of what you want answered impurities, give us a better hint. Bruce Young

Al what model of machine do you have, I can check my inventory. Hodakapartsidaho.com Bruce Young 1--208--571--2823

Hello, Hodaka World, even tho it is recommended to go to a 428 set up chain, spkt,s and etc, I believe Terry Larson had found some of the 423 sprockets in the inventory he picked up. Give him an e-mail request; terry@hodakaparts.com He will respond and keep fingures crossed he will have what you nee...

Thanks, Dan, received the pins today, will put check in the mail. See you at Hodaka Days 2019, stay safe Bruce Young

Victor I bet that the soaking in hot or boiling water for over 12hrs might work as suggested, pouring hot water on it does not allow water to soak into everything properly, Might help on outside rubber but this is stuck down inside a tube in carb. Soaking is better. Good Luck. takes time. Bruce

Gary, I personally would recommend it only as a guide, there are too many variables, when you reach out the general population some of which have no former mechanical knowledge. I can see a 16years old person with little mechanical knowledge beyond only twisting the throttle, wanting to go faster, m...

Gary, great idea, and good info sheets but be careful, when you get so many categories, it gets hard to read, Maybe break up into two sheets. Also don,t forget all models from ACE 90 on. Don,t lump groups or models together, it will confuse everyone whom follow,s lets say what is on Terry Larsons, s...

Hello, Gary, that idea for a chart would be wonderful to have for each model, when you start your charts there should be one for each, not just what bikes you have in your garage or working on at the time. Also concerning jetting, be very careful to mention type of use of where and how the bike is g...

Bob, you have treasure of early Hodaka parts and pieces, I have some of the same carbs and manifolds and I am sure the swing arms, Call me need to talk to you about this Hodaka ACE 90 stuff you picked up and what you are going to do with extras, Bruce Young

Terry Larson of Hodaka-parts INC in Missouri has built a lot of these, and has some parts and pieces as well contact him at [email protected] good guy.

Dan, Bruce Young 2995 Lower Bluff Rd., Emmett, Idaho 83617 Thanks

Dan I could use two of the pin,s I have the upper part of the tool, but do not have the pin. Let me know price. Bruce Young

Hello, to help again with this ID of the engine, slow the confusion of weather its a 90cc or 100cc engine, Thrownchain is right "E" engines generally where 100cc engine solld for just such use by several bike venders and replacement engines from stock. Look at the side cases do they both s...

FYI-- Terry Larson, has done testing on the Dunlap tires on their bikes, over the past two years, very happy with them. I know he can give the best report ever. Hodaka-parts INC, Missouri [email protected] Bruce Young

Contact this company, they have almost everything you will need, the #1 supplier of Hodaka Parts in the USA and have done a lot of work on racing the 250,s Hodaka-Parts Inc in Missouri, Terry Larson, Terry@hodaka-parts.com give them a try. I know they can give you lots of advice and equipment for th...

Kelly, Any hits or your bike yet, Hodaka World!!! t his is one heck of a good deal on a bike all prepped and ready to ride. Call Kelley before you miss out. And it can be delivered to Hodaka Days 2019. WOW what a deal. Bruce Young

Hello, Hodaka World, I have posted and will post more interesting and informative info pages from James Rozzee 20 years of work producing his great and wonderful info paper the "Hodaka Owners Registry", James is from Portland, Oregon and over the years sent this paper out to subscribers, a...

Victor, call me I have a pile of VM 20 parts and pieces, If I don,t have it I am sure we can suggest in your own town at a local m/c shop where you can get that air screw, Bruce Young you have the number

Mac, I would suspect that even a brand new never used NOS head should if one wants perfection of a sealing surface should be lapped in as well, I would bet that even a new head has some issues. I hope my thoughts are correct, if not, I am sure we will hear about it, I like Ed,s way of lapping, its d...