found time to put some parts together today...albert

Red green.. if they don't find you handsome they should at least find you handy

so thought id get this motor back together today . got my space cleaned up everything in order . figured i would put the new springs on the control shaft . who was the engineer that thought putting that little snap ring on the end of the shaft was a good idea? any way ive had a idea in mind so today...

parts are here , fly wheel at welders , most all parts cleaned up , clutch is back together from parts that i had that were in my stash . need to figure out what to do with the side casings they need some attention . will need one more order of parts before its all done but progressing on ward ...al...

Clarence is this kinda like asking who's buried in grants tomb...asking for a friend..albert

I will weld it thanks Ed your input is very much appreciated. I know a great welder. Clarence that is now your book I don't want it back, I thank you again Clarence..albert

so here's the fly wheel that Clarence sent its a fine one to , clean brand new in fact . the one with blue tape is my original one ., but it has the same model number and it has a 2F production number on it that is in the replace category. question. #1, do i run it as is ? #2 get it welded as in the...

hey clarence just checked the mail box your parts here mailman must of came late . will check it out ....albert

the book is to while away the time as you sit by the fire on those cold Montana nights . as far as hodaka days i will be in idaho 2 times this year and each time is not even close to that time dont know if i can sneak another trip in or not lot of moving parts for me this year .......albert

clutch kinda looks screwed up to i think i might be at the end of the problems

i will see if this one cleans up and let you know but if you have one that is in good shape that would be good . i will PM YOU . on a side note i bought a bunch of parts off a gentleman a couple of years ago have a combat wombat motor, of course no fly wheel or magneto assembly but i have a cylinder...

its all of the above problems . fly wheel must of came loose and wobbled and rubbed on the coils . some of the screws are even bent . im glad this came up now . i got the motor split this morning and no surprises the Kick roller retainer looks good even. no parts where they not suppose to be...... a...

wow thats great. i will take care of my part of the deal today ....albert

I did PM you with it clarence

Clarence thats pretty nice of you . i will take you up on the offer and i will make it right for you . ED i really appreciate your input and that nasa stuff is very high tec ... albert

ok im convinced . it would be very foolish of me not to take your advise . yes someone did hammer the rivets . i was able to thread the hodaka approved fly wheel puller on and remove the fly wheel . i did not take notice of the radial lines coming off of the inside rivets .so your points are well ta...

so looked at the fly wheel a little closer today and after reading the service bulletins {that i have by the way . went through the pile of bulletins i have and found them all } on it and as my engine # is out side of the numbers indicated i think its fine. but if some of you think im wrong with tha...

so looked at the fly wheel and what do you know they drilled right where you can not tell if its a 2 or a 3 , but the engine # j05281 means its not in the range of needing fix / replaced..... albert

that's interesting victor . it says construction weakness then says removed and replaced with a improved or welded unit { welded at PABATCO } , so what was welded ? and who welded them ?. i will sure check it out .....albert

todays progress . foot rest on , rear brake assembly on , kick stand on , mud flaps on , carburetor is cleaned and ready to go . so the old clutch cable broke where it screws into the side case . so took the side case off so i can un screw it and found no safety wire on the clutch , the clutch nut j...

my new steering head badge . same size as original , nice and clear with adhesive on the back . no rivets came with and flat . lots better than the one i didnt have ....albert... PS pretty bad picture it looks a lot better in person

Thanks wheel bearings are cleaned and greased . soaked the carb all night in a soapy concoction and starting to come clean

And I now have a roller

I have the spacer that replaces the speedometer

thanks victor , when you put the wheel spacer / speedometer drive , on should it be packed with grease ? ....albert